Tuner Installation Guides | Nissan TitanUpdated 4 days ago
How to Tune Your Truck with an EZ-Lynk Auto Agent 3.0
Summary
(1) - Install delete tune BEFORE installing your Exhaust & EGR delete parts
(2) - Download the EZ-Lynk App
(3) - Hook up a Battery Charger and set it to 10A
(4) - Connect Ezlynk to your Truck.
(5) - Plug Ezlynk to your OBDII Port
(5A) - Bypass Cable Installation
(6) - Connect Device to phone + connect to technician
(7) - ECU PROFILES
(8) - Monitoring Metrics.
Important Note
Your Ez Lynk should be AUTO-LINKED ALREADY. If you need to connect to a technician, please use the following emails.
POWERSTROKE 6.7L : [email protected]
GM/CHEVY/DURAMAX 6.6L : [email protected]
RAM/CUMMINS 6.7L : [email protected]
NISSAN TITAN 5.0L : [email protected]
RAM & JEEP ECODIESEL 3.0L : [email protected]
Powerstroke 3.0L : [email protected]
Please note, if we need to re-upload your tunes, it may take up to 24 hours.
(1) Install delete tune BEFORE installing your Exhaust & EGR delete parts
Tune your truck before removing the hard parts. Make sure that you tune your truck before you even think about removing your EGR or Exhaust Systems.
This way, if you have any trouble tuning your truck, you’re not dead in the water with a broken truck until Monday morning when we open back up.
(2) Download the EZ-Lynk App
Go to the App Store or the Google Play Store and download the EZ-Lynk Auto Agent App. Once downloaded, open the app and make your account.
The AutoAgent app is available for most mobile devices. It may require that your mobile device has been updated to the most recent operating system.
From the AutoAgent app, select ‘create an account’. You will need to verify that your email address is valid upon creation.
LINK TO DOWNLOAD : https://ezlynk.com/app.html
(3) Hook up a Battery Charger and set it to 10A
Hook up a battery charger. Even if your batteries are brand new and fully charged. If you don’t have a battery charger, get one and set it to a 10A charge.
The new ECM’s are very sensitive to voltage and the flash can fail if the voltage drops too low.
(4) Connect Ezlynk to your Truck.
Place Your Key in the ‘Run’ Position Turn your key all the way over to the run position without starting the vehicle.
This will boot your vehicle’s engine computer allowing the AutoAgent to communicate with it. If you have a push-to-start vehicle, you should press the Start button twice.
(5) Plug Ezlynk to your OBDII Port
Plug the EZ-Lynk into your OBDII port under the dash. If you’re flashing a 2018+ Cummins you will need to connect the Bypass Cable at the same time. (STEP 5a)
The EZ LYNK only needs to be plugged in while you install your tunes or make changes. But you can keep it in if you want to use it's gauge features.
Plug the AutoAgent into your OBD-II Port Turn your key all the way over to the run position without starting the vehicle.
This will boot your vehicle’s engine computer allowing the AutoAgent to communicate with it.
If you have a push-to-start vehicle, you should press the ‘Start’ button till it is in the run position. DO NOT START THE VEHICLE
(5A) Bypass Cable Installation
This is only for 2018+ Ram Trucks, skip this if it's not relevant. Our in depth Bypass cable installation guide can be found on our website.
The link to it is below. Go complete the steps on that guide and when you are finished, continue with Step 6.
Click Here To View The Bypass Cable Instructions
(6) Connect Device to phone + connect to technician
Open your WIFI Settings and connect to the Auto Agent via Wifi on your phone or tablet.
***Some phones give a "No Internet" message, this is normal***
Navigate to the WiFi settings of your mobile device and select the ‘EZLYNK_####’ network. A check mark will appear next to the network name when you have successfully connected.
Once you are connected you can open up the app, and the Auto Agent should detect your VIN number and recognize the connection. You’ll now see the technician you are linked with.
If There Shows No Technicians Connected, Please Use The Following Emails
POWERSTROKE 6.7L : [email protected]
GM/CHEVY/DURAMAX 6.6L : [email protected]
RAM/CUMMINS 6.7L : [email protected]
NISSAN TITAN 5.0L : [email protected]
RAM & JEEP ECODIESEL 3.0L : [email protected]
Powerstroke 3.0L : [email protected]
If none of those work on your set up, please reach out to us. Please keep note, it can take up to 24 hours for techs to re-upload the tunes, please contact us via the support form which can be found at the end of this document.
(7) ECU Profiles
Accept the technician on the device and your tune files will begin to auto-populate.
(If your cell phone does not have data, you need to exit the app and connect to Wifi and then hop back on the app to finish the linking process)
The app will default to the main dashboard. Select the button on the top left of the screen which will drop down a menu. Then, select your truck.
Select ECU Profiles from that screen, this is where your delete tunes are stored.
Select the tune file you want to use on your truck.
(IF YOU CANNOT FIND YOUR TUNE FILES, AS SHOWN ABOVE, OPEN A SUPPORT TICKET BY FOLLOWING THE STEPS AT THE END OF THIS GUIDE)
There is a cloud button to the right of the file name, it will pull the tune from the cloud and save it to your phone.
The tune that has "SOTF" is the Shift on the Fly tune. Only use this file if you install the DSP5/CSP4/CSP5 switch.
Once the file is downloaded, you can press install and the EZ-Lynk will guide you through the flash process.
Once the tune is done, it will now say Installed under the tune file.
Transmission Tune Files
If you have a Ford or GM you can now go ahead and flash your TCM Tuning.
If you have a Dodge, the TCM Tuning is packaged with Engine Tuning and only requires a single flash. It will only show you the last tune installed.
This might become confusing if you install TCM Tuning, only one will show installed even though both have been flashed!
You cannot overwrite an Engine Tune with a TCM Tune and Vice Versa.
(8) Monitoring Metrics.
If you don't plan on monitoring your parameters on your phone, you can unplug the EZ-Lynk.
You only need it plugged in when you’re using the App to monitor, flash, or diagnose.
The main dashboard is where you can view the parameters, the tiles can be adjusted and moved to your preference by holding your finger down on any tile and choosing from a list.
Need Help?
If any of these steps don't make sense, or if there is an error code or if your tune files are not present/the technician is not linked, open a support form here: https://form.jotform.com/223478868814068
Please note we have several documents on our help center which may help as well
Link 1: https://the-diesel-dudes.gorgias.help/en-US/articles/ezlynk-83048
Link 2: https://the-diesel-dudes.gorgias.help/en-US/articles/product-installation-guides-87760